57 hemi lifter problems

Contrary to popular opinion the lifter failure issue was not restricted to just MDS-equipped vehicles nor are these the so-called Hellcat lifters. I wonder if that is as-designed in the PCM specifically to keep the RPMs up above a minimum requirement for lubrication.

The exact cause seems to be undetermined but the needle roller bearings of the lifters sieze wearing a groove into the cam shaft and a misfire is then recorded.

57 hemi lifter problems. The Lions share of problems that the 57 Hemi engine users have complained about is cam and lifter failure. It happens when a stall occurs during inactivity or stopping or if the engine seizes up unexpectedly. Even amongst the users who complained.

Can anyone give me information on a factory problems with lifters and cams on 57 Hemis. Is it true they have a Class action suit against Chrysler. There is a design problem on the lifters and Cam not getting Any oil.

I saw this on a YouTube Article Which makes a lot of sense. Any information would be greatly appreciated. Sometimes in 57 Hemi ticking noise starts and in fact get adverse after heating up.

And this creates a wrong impression of these engines. Though we cant say misfires are a common problem still as it is linked with some other common issues therefore we are putting it here with the common 57 Hemi problems. Your 2019 most likely has updated parts.

I have a good friend who is a Hyundai certified master tech and is certified to work on Chrysler products. He owns two Rams with the 57 Hemi. One is a 2011 Laramie and the other is a 2018 Rebel.

He hasnt had any problems. However he runs 5W30 Mobil original instead of the recommended 5W20. Driving our new Jeep tonight.

It has a 57 Hemi MDS in it. 55mph in 8th gear knocking down the big MPG numbersbut only turning over 1300-1400 RPM. Anything less than 55mph it refuses high gear even on an easy downhill coast.

I wonder if that is as-designed in the PCM specifically to keep the RPMs up above a minimum requirement for lubrication. Yes generally the 57 has lifter chatter more so after the first time you notice it off course but not like what youre describing. Check your oil level first sign of it being low are chatty lifters.

My 09 57 sounds like a typewriter at startup until the oil gets moving. Contrary to popular opinion the lifter failure issue was not restricted to just MDS-equipped vehicles nor are these the so-called Hellcat lifters. Parts cam lifters gaskets head bolts fluids etc should run about 1750.

Labor on a 57 calls for depending on application about 10 hours. This is tied not only to lifter bleed down rates and oil viscosity but also to also to the consistent function of the refill valve within the lifter. Clearances and surface finish within the lifter are the front-line defenders of performance.

Hemi lifter tick is the inevitable result of poor manufacturing and inconsistent quality control. What year did they update the 57 lifters and cam. I have a 2007 Dodge Ram 1500 57 hemi has no spark has fuel I just put a new motor in and had electrical problems all grounds are clean and crank and cam sensors are.

What would be the approximate cost to replace the cam and lifters on a 2013 dodge 57 liter HEMI in a RAM. COMP Cams Non-MDS Lifters for Dodge Gen III HEMI Engines Designed as a major upgrade over the commonly sourced Dodge Hellcat lifters this unique design enhances oil retention around the axle and bearing helping to reduce wear and increase durability in all applications stock to high performanceNov 4 2019 COMP Cams Non-MDS Lifters for Dodge. The 57 Hemi engine has been plagued with many issues the last 10 years and this video is further discussion on the topic of lifter failure flatspotted cams.

57 Hemi MDS Problems Best Solutions Source. We are addressing the primary hurdles and their possible solutions that may come in between the efficient functioning of this engine. Most of the time the lifter roller failing problem is not really easy to understand.

This is a follow up from my previous video where I diagnosed the problem got the repair done truck just got back from a Road trip of over 2000 miles and so. These engines are known to snap exhaust manifold bolts and the MDS may be pretty stubborn at times but the most notorious problem on the 57 Hemi is the ticking noise dubbed the Hemi tick. Its not really fair to say that the lifter issue is common.

More so on the 57 yes but overall a very small percentage of the total number of 5764 engines in service across all applications. It certainly sucks big time if ones vehicle experiences it out of warranty. I 100 agree that the issue should not be a worry under 150k.

There has been much speculation about what causes the lifters to tap on some hemis especially the 57-liter V-8 however there is no technical service bulletin or recall on this engine from Dodge. If your hemi has lifters tapping it is important to check the amount of engine oil and make sure you are using the right type of oil for the vehicle. Dodge 57 Hemi hyd.

Roller lifter and cam issues. Post by CamKing Wed Jun 26 2019 539 pm 427dart wrote. Wed Jun 26 2019 511 pm Pictures I have seen show the bad lifter with a flat worn on roller and the lobe is worn down leaving a sharp shoulder on both sides.

In a fleet of cop chargers multiple lifter failures cam failures dropped valve seatsI thought the 57 gm olds diesel was the worst ever then I met the 60 powerstroke and thought it was kingBut it has been dethroned by the hemi first hydraulic roller engine I ever saw wipe cams. This question always appears in the drivers minds and the cost of replacing the engine is around 6000 to 12000 for replacing a 57 special HEMI engine. But it will cost cheaper between 3000 to 4000 if the engine re-manufactured.

The cost of installation for the HEMI engine will depend on how it is installed. My 07 Jeep with the Hemi has not had lifter problems. I think the 1st run of these 2003-2007 had problems with the dropped valve seats more than the lifters.

I discovered something about oil that was interesting. Originally Mobil 1 was the factory fill in some Chrysler models like like the SRT Grand Cherokee. As with any engine the 57L HEMI has had its share of issues over the years many of which were never widespread enough to warrant formal recalls.

Some of these problems include. Lifter failure of the Jeep Grand Cherokee 57L MDS hemi engine appears to be a pattern failure and a very expensive fix. The exact cause seems to be undetermined but the needle roller bearings of the lifters sieze wearing a groove into the cam shaft and a misfire is then recorded.

It happens to the lifters of various cylinders.